Header logo is


2016


The effect of temperature and humidity on adhesion of a gecko-inspired adhesive: implications for the natural system
The effect of temperature and humidity on adhesion of a gecko-inspired adhesive: implications for the natural system

Stark, A. Y., Klittich, M. R., Sitti, M., Niewiarowski, P. H., Dhinojwala, A.

Scientific Reports, 6, pages: 30936, Nature Publishing Group, August 2016 (article)

Abstract
The adhesive system of geckos has inspired hundreds of synthetic adhesives. While this system has been used relentlessly as a source of inspiration, less work has been done in reverse, where synthetics are used to test questions and hypotheses about the natural system. Here we take such an approach. We tested shear adhesion of a mushroom-tipped synthetic gecko adhesive under conditions that produced perplexing results in the natural adhesive system. Synthetic samples were tested at two temperatures (12 °C and 32 °C) and four different humidity levels (30%, 55%, 70%, and 80% RH). Surprisingly, adhesive performance of the synthetic samples matched that of living geckos, suggesting that uncontrolled parameters in the natural system, such as surface chemistry and material changes, may not be as influential in whole-animal performance as previously thought. There was one difference, however, when comparing natural and synthetic adhesive performance. At 12 °C and 80% RH, adhesion of the synthetic structures was lower than expected based on the natural system’s performance. Our approach highlights a unique opportunity for both biologists and material scientists, where new questions and hypotheses can be fueled by joint comparisons of the natural and synthetic systems, ultimately improving knowledge of both.

pi

DOI [BibTex]

2016


DOI [BibTex]


Magnetic propulsion of robotic sperms at low-Reynolds number
Magnetic propulsion of robotic sperms at low-Reynolds number

Khalil, I. S., Fatih Tabak, A., Klingner, A., Sitti, M.

Applied Physics Letters, 109(3):033701, AIP Publishing, July 2016 (article)

Abstract
We investigate the microswimming behaviour of robotic sperms in viscous fluids. These robotic sperms are fabricated from polystyrene dissolved in dimethyl formamide and iron-oxide nanoparticles. This composition allows the nanoparticles to be concentrated within the bead of the robotic sperm and provide magnetic dipole, whereas the flexibility of the ultra-thin tail enables flagellated locomotion using magnetic fields in millitesla range. We show that these robotic sperms have similar morphology and swimming behaviour to those of sperm cells. Moreover, we show experimentally that our robotic sperms swim controllably at an average speed of approximately one body length per second (around 125 μm s−1), and they are relatively faster than the microswimmers that depend on planar wave propulsion in low-Reynolds number fluids.

pi

DOI [BibTex]

DOI [BibTex]


Active Nanorheology with Plasmonics
Active Nanorheology with Plasmonics

Jeong, H. H., Mark, A. G., Lee, T., Alarcon-Correa, M., Eslami, S., Qiu, T., Gibbs, J. G., Fischer, P.

Nano Letters, 16(8):4887-4894, July 2016 (article)

Abstract
Nanoplasmonic systems are valued for their strong optical response and their small size. Most plasmonic sensors and systems to date have been rigid and passive. However, rendering these structures dynamic opens new possibilities for applications. Here we demonstrate that dynamic plasmonic nanoparticles can be used as mechanical sensors to selectively probe the rheological properties of a fluid in situ at the nanoscale and in microscopic volumes. We fabricate chiral magneto-plasmonic nanocolloids that can be actuated by an external magnetic field, which in turn allows for the direct and fast modulation of their distinct optical response. The method is robust and allows nanorheological measurements with a mechanical sensitivity of similar to 0.1 cP, even in strongly absorbing fluids with an optical density of up to OD similar to 3 (similar to 0.1% light transmittance) and in the presence of scatterers (e.g., 50% v/v red blood cells).

pf

DOI [BibTex]

DOI [BibTex]


no image
Acquiring and Generalizing the Embodiment Mapping from Human Observations to Robot Skills

Maeda, G., Ewerton, M., Koert, D., Peters, J.

IEEE Robotics and Automation Letters, 1(2):784-791, July 2016 (article)

ei

DOI [BibTex]

DOI [BibTex]


{Body Talk}: Crowdshaping Realistic {3D} Avatars with Words
Body Talk: Crowdshaping Realistic 3D Avatars with Words

Streuber, S., Quiros-Ramirez, M. A., Hill, M. Q., Hahn, C. A., Zuffi, S., O’Toole, A., Black, M. J.

ACM Trans. Graph. (Proc. SIGGRAPH), 35(4):54:1-54:14, July 2016 (article)

Abstract
Realistic, metrically accurate, 3D human avatars are useful for games, shopping, virtual reality, and health applications. Such avatars are not in wide use because solutions for creating them from high-end scanners, low-cost range cameras, and tailoring measurements all have limitations. Here we propose a simple solution and show that it is surprisingly accurate. We use crowdsourcing to generate attribute ratings of 3D body shapes corresponding to standard linguistic descriptions of 3D shape. We then learn a linear function relating these ratings to 3D human shape parameters. Given an image of a new body, we again turn to the crowd for ratings of the body shape. The collection of linguistic ratings of a photograph provides remarkably strong constraints on the metric 3D shape. We call the process crowdshaping and show that our Body Talk system produces shapes that are perceptually indistinguishable from bodies created from high-resolution scans and that the metric accuracy is sufficient for many tasks. This makes body “scanning” practical without a scanner, opening up new applications including database search, visualization, and extracting avatars from books.

ps

pdf web tool video talk (ppt) [BibTex]

pdf web tool video talk (ppt) [BibTex]


Six-degree-of-freedom magnetic actuation for wireless microrobotics
Six-degree-of-freedom magnetic actuation for wireless microrobotics

Diller, E., Giltinan, J., Lum, G. Z., Ye, Z., Sitti, M.

The International Journal of Robotics Research, 35(1-3):114-128, SAGE Publications Sage UK: London, England, June 2016 (article)

Abstract
Existing remotely actuated magnetic microrobots exhibit a maximum of only five-degree-of-freedom (DOF) actuation, as creation of a driving torque about the microrobot magnetization axis is not achievable. This lack of full orientation control limits the effectiveness of existing microrobots for precision tasks of object manipulation and orientation for advanced medical, biological and micromanufacturing applications. This paper presents a magnetic actuation method that allows remotely powered microrobots to achieve full six-DOF actuation by considering the case of a non-uniform magnetization profile within the microrobot body. This non-uniform magnetization allows for additional rigid-body torques to be induced from magnetic forces via a moment arm. A general analytical model presents the working principle for continuous and discrete magnetization profiles, which is applied to permanent or non-permanent (soft) magnet bodies. Several discrete-magnetization designs are also presented which possess reduced coupling between magnetic forces and induced rigid-body torques. Design guidelines are introduced which can be followed to ensure that a magnetic microrobot design is capable of six-DOF actuation. A simple permanent-magnet prototype is fabricated and used to quantitatively demonstrate the accuracy of the analytical model in a constrained-DOF environment and qualitatively for free motion in a viscous liquid three-dimensional environment. Results show that desired forces and torques can be created with high precision and limited parasitic actuation, allowing for full six-DOF actuation using limited feedback control

pi

DOI [BibTex]

DOI [BibTex]


Capturing Hands in Action using Discriminative Salient Points and Physics Simulation
Capturing Hands in Action using Discriminative Salient Points and Physics Simulation

Tzionas, D., Ballan, L., Srikantha, A., Aponte, P., Pollefeys, M., Gall, J.

International Journal of Computer Vision (IJCV), 118(2):172-193, June 2016 (article)

Abstract
Hand motion capture is a popular research field, recently gaining more attention due to the ubiquity of RGB-D sensors. However, even most recent approaches focus on the case of a single isolated hand. In this work, we focus on hands that interact with other hands or objects and present a framework that successfully captures motion in such interaction scenarios for both rigid and articulated objects. Our framework combines a generative model with discriminatively trained salient points to achieve a low tracking error and with collision detection and physics simulation to achieve physically plausible estimates even in case of occlusions and missing visual data. Since all components are unified in a single objective function which is almost everywhere differentiable, it can be optimized with standard optimization techniques. Our approach works for monocular RGB-D sequences as well as setups with multiple synchronized RGB cameras. For a qualitative and quantitative evaluation, we captured 29 sequences with a large variety of interactions and up to 150 degrees of freedom.

ps

Website pdf link (url) DOI Project Page [BibTex]

Website pdf link (url) DOI Project Page [BibTex]


System and method to magnetically actuate a capsule endoscopic robot for diagnosis and treatment
System and method to magnetically actuate a capsule endoscopic robot for diagnosis and treatment

Sitti, M., Yim, S.

May 2016, US Patent 9,445,711 (patent)

Abstract
Present invention describes a swallowable device with a soft, compliant exterior, whose shape can be changed through the use of magnetic fields, and which can be locomoted in a rolling motion through magnetic control from the exterior of the patient. The present invention could be used for a variety of medical applications inside the GI tract including but not limited to drug delivery, biopsy, heat cauterization, pH sensing, biochemical sensing, micro-surgery, and active imaging.

pi

link (url) [BibTex]


Gallium Adhesion: Phase Change of Gallium Enables Highly Reversible and Switchable Adhesion (Adv. Mater. 25/2016)
Gallium Adhesion: Phase Change of Gallium Enables Highly Reversible and Switchable Adhesion (Adv. Mater. 25/2016)

Ye, Z., Lum, G. Z., Song, S., Rich, S., Sitti, M.

Advanced Materials, 28(25):5087-5087, May 2016 (article)

Abstract
Gallium exhibits highly reversible and switchable adhesion when it undergoes a solid–liquid phase transition. The robustness of gallium is notable as it exhibits strong performance on a wide range of smooth and rough surfaces, under both dry and wet conditions. Gallium may therefore find numerous applications in transfer printing, robotics, electronic packaging, and biomedicine.

pi

DOI [BibTex]


Patterned and Specific Attachment of Bacteria on Biohybrid Bacteria-Driven Microswimmers
Patterned and Specific Attachment of Bacteria on Biohybrid Bacteria-Driven Microswimmers

Singh, A. V., Sitti, M.

Advanced Healthcare Materials, 5(18):2325-2331, May 2016 (article)

Abstract
A surface patterning technique and a specific and strong biotin–streptavidin bonding of bacteria on patterned surfaces are proposed to fabricate Janus particles that are propelled by the attached bacteria. Bacteria-driven Janus microswimmers with diameters larger than 3 μm show enhanced mean propulsion speed. Such microswimmers could be used for future applications such as targeted drug delivery and environmental remediation.

pi

DOI [BibTex]


Shape-programmable magnetic soft matter
Shape-programmable magnetic soft matter

Lum, G. Z., Ye, Z., Dong, X., Marvi, H., Erin, O., Hu, W., Sitti, M.

Proceedings of the National Academy of Sciences, 113(41):E6007–E6015, National Acad Sciences, May 2016 (article)

Abstract
Shape-programmable matter is a class of active materials whose geometry can be controlled to potentially achieve mechanical functionalities beyond those of traditional machines. Among these materials, magnetically actuated matter is particularly promising for achieving complex time-varying shapes at small scale (overall dimensions smaller than 1 cm). However, previous work can only program these materials for limited applications, as they rely solely on human intuition to approximate the required magnetization profile and actuating magnetic fields for their materials. Here, we propose a universal programming methodology that can automatically generate the required magnetization profile and actuating fields for soft matter to achieve new time-varying shapes. The universality of the proposed method can therefore inspire a vast number of miniature soft devices that are critical in robotics, smart engineering surfaces and materials, and biomedical devices. Our proposed method includes theoretical formulations, computational strategies, and fabrication procedures for programming magnetic soft matter. The presented theory and computational method are universal for programming 2D or 3D time-varying shapes, whereas the fabrication technique is generic only for creating planar beams. Based on the proposed programming method, we created a jellyfish-like robot, a spermatozoid-like undulating swimmer, and an artificial cilium that could mimic the complex beating patterns of its biological counterpart.

pi

DOI [BibTex]

DOI [BibTex]


no image
Objective assessment of robotic surgical skill using instrument contact vibrations

Gomez, E. D., Aggarwal, R., McMahan, W., Bark, K., Kuchenbecker, K. J.

Surgical Endoscopy, 30(4):1419-1431, 2016 (article)

hi

[BibTex]

[BibTex]


Inflated soft actuators with reversible stable deformations
Inflated soft actuators with reversible stable deformations

Hines, L., Petersen, K., Sitti, M.

Advanced Materials, 28(19):3690-3696, March 2016 (article)

Abstract
Most soft robotic systems are currently dependent on bulky compressors or pumps. A soft actuation method is presented combining hyperelastic membranes and dielectric elastomer actuators to switch between stable deformations of sealed chambers. This method is capable of large repeatable deformations, and has a number of stable states proportional to the number of actuatable membranes in the chamber.

pi

DOI Project Page [BibTex]


Chemotaxis of bio-hybrid multiple bacteria-driven microswimmers
Chemotaxis of bio-hybrid multiple bacteria-driven microswimmers

Zhuang, J., Sitti, M.

Scientific reports, 6, pages: 32135, Nature Publishing Group, March 2016 (article)

Abstract
In this study, in a bio-hybrid microswimmer system driven by multiple Serratia marcescens bacteria, we quantify the chemotactic drift of a large number of microswimmers towards L-serine and elucidate the associated collective chemotaxis behavior by statistical analysis of over a thousand swimming trajectories of the microswimmers. The results show that the microswimmers have a strong heading preference for moving up the L-serine gradient, while their speed does not change considerably when moving up and down the gradient; therefore, the heading bias constitutes the major factor that produces the chemotactic drift. The heading direction of a microswimmer is found to be significantly more persistent when it moves up the L-serine gradient than when it travels down the gradient; this effect causes the apparent heading preference of the microswimmers and is the crucial reason that enables the seemingly cooperative chemotaxis of multiple bacteria on a microswimmer. In addition, we find that their chemotactic drift velocity increases superquadratically with their mean swimming speed, suggesting that chemotaxis of bio-hybrid microsystems can be enhanced by designing and building faster microswimmers. Such bio-hybrid microswimmers with chemotactic steering capability may find future applications in targeted drug delivery, bioengineering, and lab-on-a-chip devices.

pi

DOI Project Page [BibTex]

DOI Project Page [BibTex]


Targeted drug delivery and imaging using mobile milli/microrobots: A promising future towards theranostic pharmaceutical design
Targeted drug delivery and imaging using mobile milli/microrobots: A promising future towards theranostic pharmaceutical design

Vikram Singh, A., Sitti, M.

Current Pharmaceutical Design, 22(11):1418-1428, Bentham Science Publishers, March 2016 (article)

Abstract
Miniature untethered medical robots have been receiving growing attention due to technological advances in microactuation, microsensors, and microfabrication and have significant potential to reduce the invasiveness and improve the accessibility of medical devices into unprecedented small spaces inside the human body. In this review, we discuss therapeutic and diagnostic applications of untethered medical microrobots. Wirelessly controlled milli/microrobots with integrated sensors are revolutionizing micromanipulation based medical interventions and are enabling doctors to perform minimally invasive procedures not possible before. 3D fabrication technologies enabling milli/microrobot fabrication at the single cell scale are empowering high-resolution visual imaging and in vivo manipulation capabilities. Swallowable millirobots and injectabale ocular microrobots allow the gastric ulcer imaging, and performance of vitreoretinal microsurgery at previously inaccessible ocular sites. Many invasive excision and incision based diagnostic biopsy, prostrate, and nephrolgical procedures can be performed minimally or almost noninvasively due to recent advancements in microrobotic technology. Advances in biohybrid microrobot systems are pushing microrobotic systems even smaller, using biological cells as on-board microactuators and microsensors using the chemical energy. Such microrobotic systems could be used for local targeted delivery of imaging contrast agents, drugs, genes, and mRNA, minimally invasive surgery, and cell micromanipulation in the near future.

pi

link (url) [BibTex]


Dispersion and shape engineered plasmonic nanosensors
Dispersion and shape engineered plasmonic nanosensors

Jeong, H. H., Mark, A. G., Alarcon-Correa, M., Kim, I., Oswald, P., Lee, T. C., Fischer, P.

Nature Communications, 7, pages: 11331, March 2016 (article)

Abstract
Biosensors based on the localized surface plasmon resonance (LSPR) of individual metallic nanoparticles promise to deliver modular, low-cost sensing with high-detection thresholds. However, they continue to suffer from relatively low sensitivity and figures of merit (FOMs). Herein we introduce the idea of sensitivity enhancement of LSPR sensors through engineering of the material dispersion function. Employing dispersion and shape engineering of chiral nanoparticles leads to remarkable refractive index sensitivities (1,091 nmRIU(-1) at lambda = 921 nm) and FOMs (>2,800 RIU-1). A key feature is that the polarization-dependent extinction of the nanoparticles is now characterized by rich spectral features, including bipolar peaks and nulls, suitable for tracking refractive index changes. This sensing modality offers strong optical contrast even in the presence of highly absorbing media, an important consideration for use in complex biological media with limited transmission. The technique is sensitive to surface-specific binding events which we demonstrate through biotin-avidin surface coupling.

pf

link (url) DOI [BibTex]


no image
Dynamic Modeling of an Out-Pipe Inspection Robot and Experimental Validation of the Proposed Model using Image Processing Technique

Sarvestani, A. A., Eghtesad, M., Fazlollahi, F., Goshtasbi, A., Mokhtari, K.

Iranian Journal of Science and Technology, Transactions of Mechanical Engineering, 40, pages: 77–85, Springer International Publishing, March 2016 (article)

Abstract
Gas and liquid pipelines surround us. To ensure reliable product delivery and to maintain pipeline integrity, asset managers should consider routine pipeline inspection and holistic management programs to extend pipeline life and prevent risk. Therefore, pipe inspection robots are of special interest to industries. In this paper, we present a new and simple locomotion strategy for an out-pipe inspection robot which can provide adjustable tractive force and can also be utilized to support active diameter adaptability. The advantages proposed by this design include simplicity, low manufacturing costs, online inspection capability and short operational time. Here a dynamic model of the robot is presented with the required assumptions. The mathematical model of 2-DOF robot is obtained using the well-known Lagrange equation. Modeling and simulations were conducted to test the validity and practicality of the proposed design and strategies. The prototype has successfully traveled along a pipe of 20 cm diameter. The results obtained from our dynamic model are then validated by experimental data.

link (url) DOI [BibTex]

link (url) DOI [BibTex]


Parallel microcracks-based ultrasensitive and highly stretchable strain sensors
Parallel microcracks-based ultrasensitive and highly stretchable strain sensors

Amjadi, M., Turan, M., Clementson, C. P., Sitti, M.

ACS Applied Materials \& Interfaces, 8(8):5618-5626, American Chemical Society, Febuary 2016 (article)

Abstract
There is an increasing demand for flexible, skin-attachable, and wearable strain sensors due to their various potential applications. However, achieving strain sensors with both high sensitivity and high stretchability is still a grand challenge. Here, we propose highly sensitive and stretchable strain sensors based on the reversible microcrack formation in composite thin films. Controllable parallel microcracks are generated in graphite thin films coated on elastomer films. Sensors made of graphite thin films with short microcracks possess high gauge factors (maximum value of 522.6) and stretchability (ε ≥ 50%), whereas sensors with long microcracks show ultrahigh sensitivity (maximum value of 11 344) with limited stretchability (ε ≤ 50%). We demonstrate the high performance strain sensing of our sensors in both small and large strain sensing applications such as human physiological activity recognition, human body large motion capturing, vibration detection, pressure sensing, and soft robotics.

pi

DOI [BibTex]

DOI [BibTex]


Stretchable, Skin-Mountable, and Wearable Strain Sensors and Their Potential Applications: A Review
Stretchable, Skin-Mountable, and Wearable Strain Sensors and Their Potential Applications: A Review

Amjadi, M., Kyung, K., Park, I., Sitti, M.

Advanced Functional Materials, 26, pages: 1678-1698, Febuary 2016 (article)

Abstract
There is a growing demand for flexible and soft electronic devices. In particular, stretchable, skin-mountable, and wearable strain sensors are needed for several potential applications including personalized health-monitoring, human motion detection, human-machine interfaces, soft robotics, and so forth. This Feature Article presents recent advancements in the development of flexible and stretchable strain sensors. The article shows that highly stretchable strain sensors are successfully being developed by new mechanisms such as disconnection between overlapped nanomaterials, crack propagation in thin films, and tunneling effect, different from traditional strain sensing mechanisms. Strain sensing performances of recently reported strain sensors are comprehensively studied and discussed, showing that appropriate choice of composite structures as well as suitable interaction between functional nanomaterials and polymers are essential for the high performance strain sensing. Next, simulation results of piezoresistivity of stretchable strain sensors by computational models are reported. Finally, potential applications of flexible strain sensors are described. This survey reveals that flexible, skin-mountable, and wearable strain sensors have potential in diverse applications while several grand challenges have to be still overcome.

pi

DOI [BibTex]

DOI [BibTex]


Remotely addressable magnetic composite micro-actuators
Remotely addressable magnetic composite micro-actuators

Sitti, M., Diller, E., Miyashita, S.

Febuary 2016, US Patent App. 15/018,008 (patent)

Abstract
The present invention describes methods to fabricate actuators that can be remotely controlled in an addressable manner, and methods to provide remote control such micro-actuators. The actuators are composites of two permanent magnet materials, one of which is has high coercivity, and the other of which switches magnetization direction by applied fields. By switching the second material's magnetization direction, the two magnets either work together or cancel each other, resulting in distinct “on” and “off” behavior of the devices. The device can be switched “on” or “off” remotely using a field pulse of short duration.

pi

[BibTex]

[BibTex]


Remotely addressable magnetic composite micro-actuators
Remotely addressable magnetic composite micro-actuators

Sitti, M., Diller, E., Miyashita, S.

Febuary 2016, US Patent 9,281,112 (patent)

Abstract
The present invention describes methods to fabricate actuators that can be remotely controlled in an addressable manner, and methods to provide remote control such micro-actuators. The actuators are composites of two permanent magnet materials, one of which is has high coercivity, and the other of which switches magnetization direction by applied fields. By switching the second material's magnetization direction, the two magnets either work together or cancel each other, resulting in distinct “on” and “off” behavior of the devices. The device can be switched “on” or “off” remotely using a field pulse of short duration.

pi

link (url) [BibTex]

link (url) [BibTex]


no image
Cutaneous Feedback of Fingertip Deformation and Vibration for Palpation in Robotic Surgery

Pacchierotti, C., Prattichizzo, D., Kuchenbecker, K. J.

IEEE Transactions on Biomedical Engineering, 63(2):278-287, February 2016 (article)

hi

[BibTex]

[BibTex]


no image
Structure modulated electrostatic deformable mirror for focus and geometry control

Nam, S., Park, S., Yun, S., Park, B., Park, S. K., Kyung, K.

Optics Express, 24(1):55-66, OSA, January 2016 (article)

Abstract
We suggest a way to electrostatically control deformed geometry of an electrostatic deformable mirror (EDM) based on geometric modulation of a basement. The EDM is composed of a metal coated elastomeric membrane (active mirror) and a polymeric basement with electrode (ground). When an electrical voltage is applied across the components, the active mirror deforms toward the stationary basement responding to electrostatic attraction force in an air gap. Since the differentiated gap distance can induce change in electrostatic force distribution between the active mirror and the basement, the EDMs are capable of controlling deformed geometry of the active mirror with different basement structures (concave, flat, and protrusive). The modulation of the deformed geometry leads to significant change in the range of the focal length of the EDMs. Even under dynamic operations, the EDM shows fairly consistent and large deformation enough to change focal length in a wide frequency range (1~175 Hz). The geometric modulation of the active mirror with dynamic focus tunability can allow the EDM to be an active mirror lens for optical zoom devices as well as an optical component controlling field of view.

hi

link (url) DOI [BibTex]

link (url) DOI [BibTex]


Size optimization of a magnetic system for drug delivery with capsule robots
Size optimization of a magnetic system for drug delivery with capsule robots

Munoz, F., Alici, G., Li, W., Sitti, M.

IEEE Transactions on Magnetics, 52(5):1-11, IEEE, January 2016 (article)

Abstract
In this paper, we present a methodology for the size optimization of an external magnetic system made of arc-shaped permanent magnets (ASMs). This magnetic system is able to remotely actuate a drug-release module embedded in a prototype of a capsule robot. The optimization of the magnetic system is carried out by using an accurate analytical model that is valid for any arbitrary dimensions of the ASMs. By using this analytical model, we perform parametric studies and conduct a statistical analysis [analysis of variance (ANOVA)] to investigate efficient ways to distribute the volume of the ASMs so that the dimensions and volume of the magnetic system are minimized while optimal flux densities and magnetic torques are obtained to actuate the drug delivery system (DDS). The ANOVA results, at 5% significance level, indicate that changes in the angular width followed by changes in the length of the ASMs have the highest impact on the magnetic linkage. Furthermore, our experimental results, which are in agreement with the analytical results, show that the size optimization of the magnetic system is effective for the actuation of the DDS in capsule robots.

pi

DOI [BibTex]

DOI [BibTex]


no image
On estimation of functional causal models: General results and application to post-nonlinear causal model

Zhang, K., Wang, Z., Zhang, J., Schölkopf, B.

ACM Transactions on Intelligent Systems and Technologies, 7(2):article no. 13, January 2016 (article)

ei

PDF DOI [BibTex]

PDF DOI [BibTex]


Magnetic Propulsion of Microswimmers with DNA-Based Flagellar Bundles
Magnetic Propulsion of Microswimmers with DNA-Based Flagellar Bundles

Maier, A. M., Weig, C., Oswald, P., Frey, E., Fischer, P., Liedl, T.

Nano Letters, 16(2):906-910, January 2016 (article)

Abstract
We show that DNA-based self-assembly can serve as a general and flexible tool to construct artificial flagella of several micrometers in length and only tens of nanometers in diameter. By attaching the DNA flagella to biocompatible magnetic microparticles, we provide a proof of concept demonstration of hybrid structures that, when rotated in an external magnetic field, propel by means of a flagellar bundle, similar to self-propelling peritrichous bacteria. Our theoretical analysis predicts that flagellar bundles that possess a length-dependent bending stiffness should exhibit a superior swimming speed compared to swimmers with a single appendage. The DNA self-assembly method permits the realization of these improved flagellar bundles in good agreement with our quantitative model. DNA flagella with well-controlled shape could fundamentally increase the functionality of fully biocompatible nanorobots and extend the scope and complexity of active materials.

pf

DOI [BibTex]

DOI [BibTex]


Human Pose Estimation from Video and IMUs
Human Pose Estimation from Video and IMUs

Marcard, T. V., Pons-Moll, G., Rosenhahn, B.

Transactions on Pattern Analysis and Machine Intelligence PAMI, 38(8):1533-1547, January 2016 (article)

ps

data pdf dataset_documentation [BibTex]

data pdf dataset_documentation [BibTex]


Gaussian Process-Based Predictive Control for Periodic Error Correction
Gaussian Process-Based Predictive Control for Periodic Error Correction

Klenske, E. D., Zeilinger, M., Schölkopf, B., Hennig, P.

IEEE Transactions on Control Systems Technology , 24(1):110-121, 2016 (article)

ei pn

PDF DOI [BibTex]

PDF DOI [BibTex]


no image
Pymanopt: A Python Toolbox for Optimization on Manifolds using Automatic Differentiation

Townsend, J., Koep, N., Weichwald, S.

Journal of Machine Learning Research, 17(137):1-5, 2016 (article)

ei

PDF Arxiv Code Project page link (url) [BibTex]


no image
A Causal, Data-driven Approach to Modeling the Kepler Data

Wang, D., Hogg, D. W., Foreman-Mackey, D., Schölkopf, B.

Publications of the Astronomical Society of the Pacific, 128(967):094503, 2016 (article)

ei

link (url) DOI Project Page [BibTex]

link (url) DOI Project Page [BibTex]


no image
Probabilistic Inference for Determining Options in Reinforcement Learning

Daniel, C., van Hoof, H., Peters, J., Neumann, G.

Machine Learning, Special Issue, 104(2):337-357, (Editors: Gärtner, T., Nanni, M., Passerini, A. and Robardet, C.), European Conference on Machine Learning im Machine Learning, Journal Track, 2016, Best Student Paper Award of ECML-PKDD 2016 (article)

am ei

DOI Project Page [BibTex]

DOI Project Page [BibTex]


Weak Supervision for Detecting Object Classes from Activities
Weak Supervision for Detecting Object Classes from Activities

Srikantha, A., Gall, J.

Computer Vision and Image Understanding (CVIU), Elsevier, 2016 (article) In press

elsevier preprint link (url) DOI [BibTex]

elsevier preprint link (url) DOI [BibTex]


Moving-horizon Nonlinear Least Squares-based Multirobot Cooperative Perception
Moving-horizon Nonlinear Least Squares-based Multirobot Cooperative Perception

Ahmad, A., Bülthoff, H.

Robotics and Autonomous Systems, 83, pages: 275-286, 2016 (article)

Abstract
In this article we present an online estimator for multirobot cooperative localization and target tracking based on nonlinear least squares minimization. Our method not only makes the rigorous optimization-based approach applicable online but also allows the estimator to be stable and convergent. We do so by employing a moving horizon technique to nonlinear least squares minimization and a novel design of the arrival cost function that ensures stability and convergence of the estimator. Through an extensive set of real robot experiments, we demonstrate the robustness of our method as well as the optimality of the arrival cost function. The experiments include comparisons of our method with i) an extended Kalman filter-based online-estimator and ii) an offline-estimator based on full-trajectory nonlinear least squares.

ps

DOI Project Page [BibTex]

DOI Project Page [BibTex]


no image
Influence of initial fixation position in scene viewing

Rothkegel, L. O. M., Trukenbrod, H. A., Schütt, H. H., Wichmann, F. A., Engbert, R.

Vision Research, 129, pages: 33-49, 2016 (article)

ei

link (url) DOI Project Page [BibTex]

link (url) DOI Project Page [BibTex]


no image
Testing models of peripheral encoding using metamerism in an oddity paradigm

Wallis, T. S. A., Bethge, M., Wichmann, F. A.

Journal of Vision, 16(2), 2016 (article)

ei

DOI Project Page [BibTex]

DOI Project Page [BibTex]


no image
Modeling Confounding by Half-Sibling Regression

Schölkopf, B., Hogg, D., Wang, D., Foreman-Mackey, D., Janzing, D., Simon-Gabriel, C. J., Peters, J.

Proceedings of the National Academy of Science, 113(27):7391-7398, 2016 (article)

ei

Code link (url) DOI Project Page [BibTex]

Code link (url) DOI Project Page [BibTex]


Dual Control for Approximate Bayesian Reinforcement Learning
Dual Control for Approximate Bayesian Reinforcement Learning

Klenske, E. D., Hennig, P.

Journal of Machine Learning Research, 17(127):1-30, 2016 (article)

ei pn

PDF link (url) [BibTex]

PDF link (url) [BibTex]


no image
A Population Based Gaussian Mixture Model Incorporating 18F-FDG-PET and DW-MRI Quantifies Tumor Tissue Classes

Divine, M. R., Katiyar, P., Kohlhofer, U., Quintanilla-Martinez, L., Disselhorst, J. A., Pichler, B. J.

Journal of Nuclear Medicine, 57(3):473-479, 2016 (article)

ei

DOI [BibTex]

DOI [BibTex]


Shape estimation of subcutaneous adipose tissue using an articulated statistical shape model
Shape estimation of subcutaneous adipose tissue using an articulated statistical shape model

Yeo, S. Y., Romero, J., Loper, M., Machann, J., Black, M.

Computer Methods in Biomechanics and Biomedical Engineering: Imaging & Visualization, 0(0):1-8, 2016 (article)

ps

publisher website preprint pdf link (url) DOI Project Page [BibTex]

publisher website preprint pdf link (url) DOI Project Page [BibTex]


Probabilistic Duality for Parallel Gibbs Sampling without Graph Coloring
Probabilistic Duality for Parallel Gibbs Sampling without Graph Coloring

Mescheder, L., Nowozin, S., Geiger, A.

Arxiv, 2016 (article)

Abstract
We present a new notion of probabilistic duality for random variables involving mixture distributions. Using this notion, we show how to implement a highly-parallelizable Gibbs sampler for weakly coupled discrete pairwise graphical models with strictly positive factors that requires almost no preprocessing and is easy to implement. Moreover, we show how our method can be combined with blocking to improve mixing. Even though our method leads to inferior mixing times compared to a sequential Gibbs sampler, we argue that our method is still very useful for large dynamic networks, where factors are added and removed on a continuous basis, as it is hard to maintain a graph coloring in this setup. Similarly, our method is useful for parallelizing Gibbs sampling in graphical models that do not allow for graph colorings with a small number of colors such as densely connected graphs.

avg

pdf [BibTex]


no image
Painfree and accurate Bayesian estimation of psychometric functions for (potentially) overdispersed data

Schütt, H. H., Harmeling, S., Macke, J. H., Wichmann, F. A.

Vision Research, 122, pages: 105-123, 2016 (article)

ei

link (url) DOI Project Page [BibTex]

link (url) DOI Project Page [BibTex]


no image
Hydrodynamic simulations of the interaction between giant stars and planets

Staff, J., De Marco, O., Wood, P., Galaviz, P., Passy, J.

Monthly Notices of the Royal Astronomical Society, 458, pages: 832-844, 2016 (article)

DOI [BibTex]

DOI [BibTex]


no image
Peripheral vs. central determinants of vibrotactile adaptation

Klöcker, A., Gueorguiev, D., Thonnard, J. L., Mouraux, A.

Journal of Neurophysiology, 115(2):685-691, 2016, PMID: 26581868 (article)

Abstract
Long-lasting mechanical vibrations applied to the skin induce a reversible decrease in the perception of vibration at the stimulated skin site. This phenomenon of vibrotactile adaptation has been studied extensively, yet there is still no clear consensus on the mechanisms leading to vibrotactile adaptation. In particular, the respective contributions of 1) changes affecting mechanical skin impedance, 2) peripheral processes, and 3) central processes are largely unknown. Here we used direct electrical stimulation of nerve fibers to bypass mechanical transduction processes and thereby explore the possible contribution of central vs. peripheral processes to vibrotactile adaptation. Three experiments were conducted. In the first, adaptation was induced with mechanical vibration of the fingertip (51- or 251-Hz vibration delivered for 8 min, at 40× detection threshold). In the second, we attempted to induce adaptation with transcutaneous electrical stimulation of the median nerve (51- or 251-Hz constant-current pulses delivered for 8 min, at 1.5× detection threshold). Vibrotactile detection thresholds were measured before and after adaptation. Mechanical stimulation induced a clear increase of vibrotactile detection thresholds. In contrast, thresholds were unaffected by electrical stimulation. In the third experiment, we assessed the effect of mechanical adaptation on the detection thresholds to transcutaneous electrical nerve stimuli, measured before and after adaptation. Electrical detection thresholds were unaffected by the mechanical adaptation. Taken together, our results suggest that vibrotactile adaptation is predominantly the consequence of peripheral mechanoreceptor processes and/or changes in biomechanical properties of the skin.

hi

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
On designing an active tail for legged robots: simplifying control via decoupling of control objectives

Heim, S. W., Ajallooeian, M., Eckert, P., Vespignani, M., Ijspeert, A. J.

Industrial Robot: An International Journal, 43, pages: 338-346, Emerald Group Publishing Limited, 2016 (article)

dlg

Preprint [BibTex]

Preprint [BibTex]


no image
NimbRo Explorer: Semi-Autonomous Exploration and Mobile Manipulation in Rough Terrain

Stueckler, J., Schwarz, M., Schadler, M., Topalidou-Kyniazopoulou, A., Behnke, S.

Journal of Field Robotics (JFR), 33(4):411-430, Wiley, 2016 (article)

ev

[BibTex]

[BibTex]


no image
Stochastic search with Poisson and deterministic resetting

Bhat, U., De Bacco, C., Redner, S.

Journal of Statistical Mechanics: Theory and Experiment, 2016(8):083401, IOP Publishing, 2016 (article)

pio

Preprint link (url) [BibTex]

Preprint link (url) [BibTex]