Header logo is


2019


Thumb xl motorized device
Implementation of a 6-DOF Parallel Continuum Manipulator for Delivering Fingertip Tactile Cues

Young, E. M., Kuchenbecker, K. J.

IEEE Transactions on Haptics, 12(3):295-306, June 2019 (article)

Abstract
Existing fingertip haptic devices can deliver different subsets of tactile cues in a compact package, but we have not yet seen a wearable six-degree-of-freedom (6-DOF) display. This paper presents the Fuppeteer (short for Fingertip Puppeteer), a device that is capable of controlling the position and orientation of a flat platform, such that any combination of normal and shear force can be delivered at any location on any human fingertip. We build on our previous work of designing a parallel continuum manipulator for fingertip haptics by presenting a motorized version in which six flexible Nitinol wires are actuated via independent roller mechanisms and proportional-derivative controllers. We evaluate the settling time and end-effector vibrations observed during system responses to step inputs. After creating a six-dimensional lookup table and adjusting simulated inputs using measured Jacobians, we show that the device can make contact with all parts of the fingertip with a mean error of 1.42 mm. Finally, we present results from a human-subject study. A total of 24 users discerned 9 evenly distributed contact locations with an average accuracy of 80.5%. Translational and rotational shear cues were identified reasonably well near the center of the fingertip and more poorly around the edges.

hi

DOI [BibTex]


Thumb xl trimpe2019resource image
Resource-aware IoT Control: Saving Communication through Predictive Triggering

Trimpe, S., Baumann, D.

IEEE Internet of Things Journal, 6(3):5013-5028, June 2019 (article)

Abstract
The Internet of Things (IoT) interconnects multiple physical devices in large-scale networks. When the 'things' coordinate decisions and act collectively on shared information, feedback is introduced between them. Multiple feedback loops are thus closed over a shared, general-purpose network. Traditional feedback control is unsuitable for design of IoT control because it relies on high-rate periodic communication and is ignorant of the shared network resource. Therefore, recent event-based estimation methods are applied herein for resource-aware IoT control allowing agents to decide online whether communication with other agents is needed, or not. While this can reduce network traffic significantly, a severe limitation of typical event-based approaches is the need for instantaneous triggering decisions that leave no time to reallocate freed resources (e.g., communication slots), which hence remain unused. To address this problem, novel predictive and self triggering protocols are proposed herein. From a unified Bayesian decision framework, two schemes are developed: self triggers that predict, at the current triggering instant, the next one; and predictive triggers that check at every time step, whether communication will be needed at a given prediction horizon. The suitability of these triggers for feedback control is demonstrated in hardware experiments on a cart-pole, and scalability is discussed with a multi-vehicle simulation.

ics

PDF arXiv DOI [BibTex]

PDF arXiv DOI [BibTex]


no image
The Perception of Ultrasonic Square Reductions of Friction With Variable Sharpness and Duration

Gueorguiev, D., Vezzoli, E., Sednaoui, T., Grisoni, L., Lemaire-Semail, B.

IEEE Transactions on Haptics, 12(2):179-188, January 2019 (article)

Abstract
The human perception of square ultrasonic modulation of the finger-surface friction was investigated during active tactile exploration by using short frictional cues of varying duration and sharpness. In a first experiment, we asked participants to discriminate the transition time and duration of short square ultrasonic reductions of friction. They proved very sensitive to discriminate millisecond differences in these two parameters with the average psychophysical thresholds being 2.3–2.4 ms for both parameters. A second experiment focused on the perception of square friction reductions with variable transition times and durations. We found that for durations of the stimulation larger than 90 ms, participants often perceived three or four edges when only two stimulations were presented while they consistently felt two edges for signals shorter than 50 ms. A subsequent analysis of the contact forces induced by these ultrasonic stimulations during slow and fast active exploration showed that two identical consecutive ultrasonic pulses can induce significantly different frictional dynamics especially during fast motion of the finger. These results confirm the human sensitivity to transient frictional cues and suggest that the human perception of square reductions of friction can depend on their sharpness and duration as well as on the speed of exploration.

hi

DOI [BibTex]

DOI [BibTex]


Thumb xl journal iav
Data-efficient Auto-tuning with Bayesian Optimization: An Industrial Control Study

Neumann-Brosig, M., Marco, A., Schwarzmann, D., Trimpe, S.

IEEE Transactions on Control Systems Technology, 2019 (article) Accepted

Abstract
Bayesian optimization is proposed for automatic learning of optimal controller parameters from experimental data. A probabilistic description (a Gaussian process) is used to model the unknown function from controller parameters to a user-defined cost. The probabilistic model is updated with data, which is obtained by testing a set of parameters on the physical system and evaluating the cost. In order to learn fast, the Bayesian optimization algorithm selects the next parameters to evaluate in a systematic way, for example, by maximizing information gain about the optimum. The algorithm thus iteratively finds the globally optimal parameters with only few experiments. Taking throttle valve control as a representative industrial control example, the proposed auto-tuning method is shown to outperform manual calibration: it consistently achieves better performance with a low number of experiments. The proposed auto-tuning framework is flexible and can handle different control structures and objectives.

ics

arXiv (PDF) DOI Project Page [BibTex]

arXiv (PDF) DOI Project Page [BibTex]


no image
How Does It Feel to Clap Hands with a Robot?

Fitter, N. T., Kuchenbecker, K. J.

International Journal of Social Robotics, 2019 (article) Accepted

Abstract
Future robots may need lighthearted physical interaction capabilities to connect with people in meaningful ways. To begin exploring how users perceive playful human–robot hand-to-hand interaction, we conducted a study with 20 participants. Each user played simple hand-clapping games with the Rethink Robotics Baxter Research Robot during a 1-h-long session involving 24 randomly ordered conditions that varied in facial reactivity, physical reactivity, arm stiffness, and clapping tempo. Survey data and experiment recordings demonstrate that this interaction is viable: all users successfully completed the experiment and mentioned enjoying at least one game without prompting. Hand-clapping tempo was highly salient to users, and human-like robot errors were more widely accepted than mechanical errors. Furthermore, perceptions of Baxter varied in the following statistically significant ways: facial reactivity increased the robot’s perceived pleasantness and energeticness; physical reactivity decreased pleasantness, energeticness, and dominance; higher arm stiffness increased safety and decreased dominance; and faster tempo increased energeticness and increased dominance. These findings can motivate and guide roboticists who want to design social–physical human–robot interactions.

hi

[BibTex]

[BibTex]


Thumb xl mode changes long exp
Fast Feedback Control over Multi-hop Wireless Networks with Mode Changes and Stability Guarantees

Baumann, D., Mager, F., Jacob, R., Thiele, L., Zimmerling, M., Trimpe, S.

ACM Transactions on Cyber-Physical Systems, 2019 (article) Accepted

ics

arXiv PDF [BibTex]

arXiv PDF [BibTex]

2017


no image
Evaluation of High-Fidelity Simulation as a Training Tool in Transoral Robotic Surgery

Bur, A. M., Gomez, E. D., Newman, J. G., Weinstein, G. S., Bert W. O’Malley, J., Rassekh, C. H., Kuchenbecker, K. J.

Laryngoscope, 127(12):2790-2795, December 2017 (article)

hi

DOI [BibTex]

2017


DOI [BibTex]


Thumb xl oe
Electrically tunable binary phase Fresnel lens based on a dielectric elastomer actuator

Park, S., Park, B., Nam, S., Yun, S., Park, S. K., Mun, S., Lim, J. M., Ryu, Y., Song, S. H., Kyung, K.

Optics Express, 25(20):23801-23808, OSA, October 2017 (article)

Abstract
We propose and demonstrate an all-solid-state tunable binary phase Fresnel lens with electrically controllable focal length. The lens is composed of a binary phase Fresnel zone plate, a circular acrylic frame, and a dielectric elastomer (DE) actuator which is made of a thin DE layer and two compliant electrodes using silver nanowires. Under electric potential, the actuator produces in-plane deformation in a radial direction that can compress the Fresnel zones. The electrically-induced deformation compresses the Fresnel zones to be contracted as high as 9.1 % and changes the focal length, getting shorter from 20.0 cm to 14.5 cm. The measured change in the focal length of the fabricated lens is consistent with the result estimated from numerical simulation.

hi

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Using Contact Forces and Robot Arm Accelerations to Automatically Rate Surgeon Skill at Peg Transfer

Brown, J. D., O’Brien, C. E., Leung, S. C., Dumon, K. R., Lee, D. I., Kuchenbecker, K. J.

IEEE Transactions on Biomedical Engineering, 64(9):2263-2275, September 2017 (article)

hi

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Ungrounded Haptic Augmented Reality System for Displaying Texture and Friction

Culbertson, H., Kuchenbecker, K. J.

IEEE/ASME Transactions on Mechatronics, 22(4):1839-1849, August 2017 (article)

hi

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
A variation in wrinkle structures of UV-cured films with chemical structures of prepolymers

Park, S. K., Kwark, Y., Nam, S., Moon, J., Kim, D. W., Park, S., Park, B., Yun, S., Lee, J., Yu, B., Kyung, K.

Materials Letters, 199, pages: 105-109, July 2017 (article)

Abstract
Spontaneously wrinkled films can be easily obtained from UV-crosslinkable liquid prepolymers under special UV-curing conditions. They vary wrinkle structures of the UV-cured films and, however, cannot be precisely controlled. Here, five different UV-crosslinkable prepolymers are synthesized to study the chemical structure effect of prepolymers on wrinkle formation and modulation of the UV-cured films irrespective of the UV-curing conditions. Both wavelength and amplitude of the wrinkles are tuned with the different liquid prepolymers from 4.10 to 5.63µm and from 1.00 to 1.66µm, respectively. The wrinkle structures of the UV-cured films are faded by adding a solid prepolymer to a liquid prepolymer due to interference from it in the shrinkage of the liquid prepolymer layer. The wrinkles completely disappear in the UV-cured films fabricated from the formulated prepolymers containing over 50wt% of the solid prepolymer.

hi

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Event-based State Estimation: An Emulation-based Approach

Trimpe, S.

IET Control Theory & Applications, 11(11):1684-1693, July 2017 (article)

Abstract
An event-based state estimation approach for reducing communication in a networked control system is proposed. Multiple distributed sensor agents observe a dynamic process and sporadically transmit their measurements to estimator agents over a shared bus network. Local event-triggering protocols ensure that data is transmitted only when necessary to meet a desired estimation accuracy. The event-based design is shown to emulate the performance of a centralised state observer design up to guaranteed bounds, but with reduced communication. The stability results for state estimation are extended to the distributed control system that results when the local estimates are used for feedback control. Results from numerical simulations and hardware experiments illustrate the effectiveness of the proposed approach in reducing network communication.

am ics

arXiv Supplementary material PDF DOI Project Page [BibTex]

arXiv Supplementary material PDF DOI Project Page [BibTex]


no image
Perception of Force and Stiffness in the Presence of Low-Frequency Haptic Noise

Gurari, N., Okamura, A. M., Kuchenbecker, K. J.

PLoS ONE, 12(6):e0178605, June 2017 (article)

hi

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Evaluation of a Vibrotactile Simulator for Dental Caries Detection

Kuchenbecker, K. J., Parajon, R., Maggio, M. P.

Simulation in Healthcare, 12(3):148-156, June 2017 (article)

hi

DOI [BibTex]

DOI [BibTex]


no image
Importance of Matching Physical Friction, Hardness, and Texture in Creating Realistic Haptic Virtual Surfaces

Culbertson, H., Kuchenbecker, K. J.

IEEE Transactions on Haptics, 10(1):63-74, January 2017 (article)

hi

[BibTex]


no image
Effects of Grip-Force, Contact, and Acceleration Feedback on a Teleoperated Pick-and-Place Task

Khurshid, R. P., Fitter, N. T., Fedalei, E. A., Kuchenbecker, K. J.

IEEE Transactions on Haptics, 10(1):40-53, January 2017 (article)

hi

[BibTex]

[BibTex]


no image
The tactile perception of transient changes in friction

Gueorguiev, D., Vezzoli, E., Mouraux, A., Lemaire-Semail, B., Thonnard, J.

Journal of The Royal Society Interface, 14(137), The Royal Society, 2017 (article)

Abstract
When we touch an object or explore a texture, frictional strains are induced by the tactile interactions with the surface of the object. Little is known about how these interactions are perceived, although it becomes crucial for the nascent industry of interactive displays with haptic feedback (e.g. smartphones and tablets) where tactile feedback based on friction modulation is particularly relevant. To investigate the human perception of frictional strains, we mounted a high-fidelity friction modulating ultrasonic device on a robotic platform performing controlled rubbing of the fingertip and asked participants to detect induced decreases of friction during a forced-choice task. The ability to perceive the changes in friction was found to follow Weber{\textquoteright}s Law of just noticeable differences, as it consistently depended on the ratio between the reduction in tangential force and the pre-stimulation tangential force. The Weber fraction was 0.11 in all conditions demonstrating a very high sensitivity to transient changes in friction. Humid fingers experienced less friction reduction than drier ones for the same intensity of ultrasonic vibration but the Weber fraction for detecting changes in friction was not influenced by the humidity of the skin.

hi

link (url) DOI [BibTex]

link (url) DOI [BibTex]


Thumb xl screen shot 2018 05 04 at 11.37.41
Effect of Waveform on Tactile Perception by Electrovibration Displayed on Touch Screens

Vardar, Y., Güçlü, B., Basdogan, C.

IEEE Transactions on Haptics, 10(4):488-499, 2017 (article)

Abstract
In this study, we investigated the effect of input voltage waveform on our haptic perception of electrovibration on touch screens. Through psychophysical experiments performed with eight subjects, we first measured the detection thresholds of electrovibration stimuli generated by sinusoidal and square voltages at various fundamental frequencies. We observed that the subjects were more sensitive to stimuli generated by square wave voltage than sinusoidal one for frequencies lower than 60 Hz. Using Matlab simulations, we showed that the sensation difference of waveforms in low fundamental frequencies occurred due to the frequency-dependent electrical properties of human skin and human tactile sensitivity. To validate our simulations, we conducted a second experiment with another group of eight subjects. We first actuated the touch screen at the threshold voltages estimated in the first experiment and then measured the contact force and acceleration acting on the index fingers of the subjects moving on the screen with a constant speed. We analyzed the collected data in the frequency domain using the human vibrotactile sensitivity curve. The results suggested that Pacinian channel was the primary psychophysical channel in the detection of the electrovibration stimuli caused by all the square-wave inputs tested in this study. We also observed that the measured force and acceleration data were affected by finger speed in a complex manner suggesting that it may also affect our haptic perception accordingly.

hi

vardar_toh2017 DOI [BibTex]

vardar_toh2017 DOI [BibTex]

2016


Thumb xl nonlinear approximate vs exact
A New Perspective and Extension of the Gaussian Filter

Wüthrich, M., Trimpe, S., Garcia Cifuentes, C., Kappler, D., Schaal, S.

The International Journal of Robotics Research, 35(14):1731-1749, December 2016 (article)

Abstract
The Gaussian Filter (GF) is one of the most widely used filtering algorithms; instances are the Extended Kalman Filter, the Unscented Kalman Filter and the Divided Difference Filter. The GF represents the belief of the current state by a Gaussian distribution, whose mean is an affine function of the measurement. We show that this representation can be too restrictive to accurately capture the dependences in systems with nonlinear observation models, and we investigate how the GF can be generalized to alleviate this problem. To this end, we view the GF as the solution to a constrained optimization problem. From this new perspective, the GF is seen as a special case of a much broader class of filters, obtained by relaxing the constraint on the form of the approximate posterior. On this basis, we outline some conditions which potential generalizations have to satisfy in order to maintain the computational efficiency of the GF. We propose one concrete generalization which corresponds to the standard GF using a pseudo measurement instead of the actual measurement. Extending an existing GF implementation in this manner is trivial. Nevertheless, we show that this small change can have a major impact on the estimation accuracy.

am ics

PDF DOI Project Page [BibTex]

2016


PDF DOI Project Page [BibTex]


no image
An electro-active polymer based lens module for dynamically varying focal system

Yun, S., Park, S., Nam, S., Park, B., Park, S. K., Mun, S., Lim, J. M., Kyung, K.

Applied Physics Letters, 109(14):141908, October 2016 (article)

Abstract
We demonstrate a polymer-based active-lens module allowing a dynamic focus controllable optical system with a wide tunable range. The active-lens module is composed of parallelized two active- lenses with a convex and a concave shaped hemispherical lens structure, respectively. Under opera- tion with dynamic input voltage signals, each active-lens produces translational movement bi-directionally responding to a hybrid driving force that is a combination of an electro-active response of a thin dielectric elastomer membrane and an electro-static attraction force. Since the proposed active lens module widely modulates a gap-distance between lens-elements, an optical system based on the active-lens module provides widely-variable focusing for selective imaging of objects in arbitrary position.

hi

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Wrinkle structures formed by formulating UV-crosslinkable liquid prepolymers

Park, S. K., Kwark, Y., Nam, S., Park, S., Park, B., Yun, S., Moon, J., Lee, J., Yu, B., Kyung, K.

Polymer, 99, pages: 447-452, September 2016 (article)

Abstract
Artificial wrinkles have recently been in the spotlight due to their potential use in high-tech applications. A spontaneously wrinkled film can be fabricated from UV-crosslinkable liquid prepolymers. Here, we controlled the wrinkle formation by simply formulating two UV-crosslinkable liquid prepolymers, tetraethylene glycol bis(4-ethenyl-2,3,5,6-tetrafluorophenyl) ether (TEGDSt) and tetraethylene glycol diacrylate (TEGDA). The wrinkles were formed from the TEGDSt/TEGDA formulated prepolymer layers containing up to 30 wt% of TEGDA. The wrinkle formation depended upon the rate of photo-crosslinking reaction of the formulated prepolymers. The first order apparent rate constant, kapp, was between ca. 5.7 × 10−3 and 12.2 × 10−3 s−1 for the wrinkle formation. The wrinkle structures were modulated within the kapp mainly due to variation in the extent of shrinkage of the formulated prepolymer layers with the content of TEGDA

hi

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Objective assessment of robotic surgical skill using instrument contact vibrations

Gomez, E. D., Aggarwal, R., McMahan, W., Bark, K., Kuchenbecker, K. J.

Surgical Endoscopy, 30(4):1419-1431, 2016 (article)

hi

[BibTex]

[BibTex]


no image
Cutaneous Feedback of Fingertip Deformation and Vibration for Palpation in Robotic Surgery

Pacchierotti, C., Prattichizzo, D., Kuchenbecker, K. J.

IEEE Transactions on Biomedical Engineering, 63(2):278-287, February 2016 (article)

hi

[BibTex]

[BibTex]


no image
Structure modulated electrostatic deformable mirror for focus and geometry control

Nam, S., Park, S., Yun, S., Park, B., Park, S. K., Kyung, K.

Optics Express, 24(1):55-66, OSA, January 2016 (article)

Abstract
We suggest a way to electrostatically control deformed geometry of an electrostatic deformable mirror (EDM) based on geometric modulation of a basement. The EDM is composed of a metal coated elastomeric membrane (active mirror) and a polymeric basement with electrode (ground). When an electrical voltage is applied across the components, the active mirror deforms toward the stationary basement responding to electrostatic attraction force in an air gap. Since the differentiated gap distance can induce change in electrostatic force distribution between the active mirror and the basement, the EDMs are capable of controlling deformed geometry of the active mirror with different basement structures (concave, flat, and protrusive). The modulation of the deformed geometry leads to significant change in the range of the focal length of the EDMs. Even under dynamic operations, the EDM shows fairly consistent and large deformation enough to change focal length in a wide frequency range (1~175 Hz). The geometric modulation of the active mirror with dynamic focus tunability can allow the EDM to be an active mirror lens for optical zoom devices as well as an optical component controlling field of view.

hi

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Peripheral vs. central determinants of vibrotactile adaptation

Klöcker, A., Gueorguiev, D., Thonnard, J. L., Mouraux, A.

Journal of Neurophysiology, 115(2):685-691, 2016, PMID: 26581868 (article)

Abstract
Long-lasting mechanical vibrations applied to the skin induce a reversible decrease in the perception of vibration at the stimulated skin site. This phenomenon of vibrotactile adaptation has been studied extensively, yet there is still no clear consensus on the mechanisms leading to vibrotactile adaptation. In particular, the respective contributions of 1) changes affecting mechanical skin impedance, 2) peripheral processes, and 3) central processes are largely unknown. Here we used direct electrical stimulation of nerve fibers to bypass mechanical transduction processes and thereby explore the possible contribution of central vs. peripheral processes to vibrotactile adaptation. Three experiments were conducted. In the first, adaptation was induced with mechanical vibration of the fingertip (51- or 251-Hz vibration delivered for 8 min, at 40× detection threshold). In the second, we attempted to induce adaptation with transcutaneous electrical stimulation of the median nerve (51- or 251-Hz constant-current pulses delivered for 8 min, at 1.5× detection threshold). Vibrotactile detection thresholds were measured before and after adaptation. Mechanical stimulation induced a clear increase of vibrotactile detection thresholds. In contrast, thresholds were unaffected by electrical stimulation. In the third experiment, we assessed the effect of mechanical adaptation on the detection thresholds to transcutaneous electrical nerve stimuli, measured before and after adaptation. Electrical detection thresholds were unaffected by the mechanical adaptation. Taken together, our results suggest that vibrotactile adaptation is predominantly the consequence of peripheral mechanoreceptor processes and/or changes in biomechanical properties of the skin.

hi

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Silent Expectations: Dynamic Causal Modeling of Cortical Prediction and Attention to Sounds That Weren’t

Chennu, S., Noreika, V., Gueorguiev, D., Shtyrov, Y., Bekinschtein, T. A., Henson, R.

Journal of Neuroscience, 36(32):8305-8316, Society for Neuroscience, 2016 (article)

Abstract
There is increasing evidence that human perception is realized by a hierarchy of neural processes in which predictions sent backward from higher levels result in prediction errors that are fed forward from lower levels, to update the current model of the environment. Moreover, the precision of prediction errors is thought to be modulated by attention. Much of this evidence comes from paradigms in which a stimulus differs from that predicted by the recent history of other stimuli (generating a so-called {\textquotedblleft}mismatch response{\textquotedblright}). There is less evidence from situations where a prediction is not fulfilled by any sensory input (an {\textquotedblleft}omission{\textquotedblright} response). This situation arguably provides a more direct measure of {\textquotedblleft}top-down{\textquotedblright} predictions in the absence of confounding {\textquotedblleft}bottom-up{\textquotedblright} input. We applied Dynamic Causal Modeling of evoked electromagnetic responses recorded by EEG and MEG to an auditory paradigm in which we factorially crossed the presence versus absence of {\textquotedblleft}bottom-up{\textquotedblright} stimuli with the presence versus absence of {\textquotedblleft}top-down{\textquotedblright} attention. Model comparison revealed that both mismatch and omission responses were mediated by increased forward and backward connections, differing primarily in the driving input. In both responses, modeling results suggested that the presence of attention selectively modulated backward {\textquotedblleft}prediction{\textquotedblright} connections. Our results provide new model-driven evidence of the pure top-down prediction signal posited in theories of hierarchical perception, and highlight the role of attentional precision in strengthening this prediction.SIGNIFICANCE STATEMENT Human auditory perception is thought to be realized by a network of neurons that maintain a model of and predict future stimuli. Much of the evidence for this comes from experiments where a stimulus unexpectedly differs from previous ones, which generates a well-known {\textquotedblleft}mismatch response.{\textquotedblright} But what happens when a stimulus is unexpectedly omitted altogether? By measuring the brain{\textquoteright}s electromagnetic activity, we show that it also generates an {\textquotedblleft}omission response{\textquotedblright} that is contingent on the presence of attention. We model these responses computationally, revealing that mismatch and omission responses only differ in the location of inputs into the same underlying neuronal network. In both cases, we show that attention selectively strengthens the brain{\textquoteright}s prediction of the future.

hi

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Event-based Sampling for Reducing Communication Load in Realtime Human Motion Analysis by Wireless Inertial Sensor Networks

Laidig, D., Trimpe, S., Seel, T.

Current Directions in Biomedical Engineering, 2(1):711-714, De Gruyter, 2016 (article)

am ics

PDF DOI [BibTex]

PDF DOI [BibTex]


no image
Touch uses frictional cues to discriminate flat materials

Gueorguiev, D., Bochereau, S., Mouraux, A., Hayward, V., Thonnard, J.

Scientific reports, 6, pages: 25553, Nature Publishing Group, 2016 (article)

hi

[BibTex]

[BibTex]