Header logo is


2017


no image
Pattern Generation for Walking on Slippery Terrains

Khadiv, M., Moosavian, S. A. A., Herzog, A., Righetti, L.

In 2017 5th International Conference on Robotics and Mechatronics (ICROM), Iran, August 2017 (inproceedings)

Abstract
In this paper, we extend state of the art Model Predictive Control (MPC) approaches to generate safe bipedal walking on slippery surfaces. In this setting, we formulate walking as a trade off between realizing a desired walking velocity and preserving robust foot-ground contact. Exploiting this for- mulation inside MPC, we show that safe walking on various flat terrains can be achieved by compromising three main attributes, i. e. walking velocity tracking, the Zero Moment Point (ZMP) modulation, and the Required Coefficient of Friction (RCoF) regulation. Simulation results show that increasing the walking velocity increases the possibility of slippage, while reducing the slippage possibility conflicts with reducing the tip-over possibility of the contact and vice versa.

mg

link (url) [BibTex]

2017


link (url) [BibTex]

2012


no image
Encoding of Periodic and their Transient Motions by a Single Dynamic Movement Primitive

Ernesti, J., Righetti, L., Do, M., Asfour, T., Schaal, S.

In 2012 12th IEEE-RAS International Conference on Humanoid Robots (Humanoids 2012), pages: 57-64, IEEE, Osaka, Japan, November 2012 (inproceedings)

am mg

link (url) DOI [BibTex]

2012


link (url) DOI [BibTex]


no image
Learning Force Control Policies for Compliant Robotic Manipulation

Kalakrishnan, M., Righetti, L., Pastor, P., Schaal, S.

In ICML’12 Proceedings of the 29th International Coference on International Conference on Machine Learning, pages: 49-50, Edinburgh, Scotland, 2012 (inproceedings)

am mg

[BibTex]

[BibTex]


no image
Spin wave mediated magnetic vortex core reversal

Stoll, H.

In 8461, San Diego, California, USA, 2012 (inproceedings)

mms

DOI [BibTex]

DOI [BibTex]


no image
Quadratic programming for inverse dynamics with optimal distribution of contact forces

Righetti, L., Schaal, S.

In 2012 12th IEEE-RAS International Conference on Humanoid Robots (Humanoids 2012), pages: 538-543, IEEE, Osaka, Japan, November 2012 (inproceedings)

Abstract
In this contribution we propose an inverse dynamics controller for a humanoid robot that exploits torque redundancy to minimize any combination of linear and quadratic costs in the contact forces and the commands. In addition the controller satisfies linear equality and inequality constraints in the contact forces and the commands such as torque limits, unilateral contacts or friction cones limits. The originality of our approach resides in the formulation of the problem as a quadratic program where we only need to solve for the control commands and where the contact forces are optimized implicitly. Furthermore, we do not need a structured representation of the dynamics of the robot (i.e. an explicit computation of the inertia matrix). It is in contrast with existing methods based on quadratic programs. The controller is then robust to uncertainty in the estimation of the dynamics model and the optimization is fast enough to be implemented in high bandwidth torque control loops that are increasingly available on humanoid platforms. We demonstrate properties of our controller with simulations of a human size humanoid robot.

am mg

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Towards Associative Skill Memories

Pastor, P., Kalakrishnan, M., Righetti, L., Schaal, S.

In 2012 12th IEEE-RAS International Conference on Humanoid Robots (Humanoids 2012), pages: 309-315, IEEE, Osaka, Japan, November 2012 (inproceedings)

Abstract
Movement primitives as basis of movement planning and control have become a popular topic in recent years. The key idea of movement primitives is that a rather small set of stereotypical movements should suffice to create a large set of complex manipulation skills. An interesting side effect of stereotypical movement is that it also creates stereotypical sensory events, e.g., in terms of kinesthetic variables, haptic variables, or, if processed appropriately, visual variables. Thus, a movement primitive executed towards a particular object in the environment will associate a large number of sensory variables that are typical for this manipulation skill. These association can be used to increase robustness towards perturbations, and they also allow failure detection and switching towards other behaviors. We call such movement primitives augmented with sensory associations Associative Skill Memories (ASM). This paper addresses how ASMs can be acquired by imitation learning and how they can create robust manipulation skill by determining subsequent ASMs online to achieve a particular manipulation goal. Evaluation for grasping and manipulation with a Barrett WAM/Hand illustrate our approach.

am mg

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Template-based learning of grasp selection

Herzog, A., Pastor, P., Kalakrishnan, M., Righetti, L., Asfour, T., Schaal, S.

In 2012 IEEE International Conference on Robotics and Automation, pages: 2379-2384, IEEE, Saint Paul, USA, 2012 (inproceedings)

Abstract
The ability to grasp unknown objects is an important skill for personal robots, which has been addressed by many present and past research projects, but still remains an open problem. A crucial aspect of grasping is choosing an appropriate grasp configuration, i.e. the 6d pose of the hand relative to the object and its finger configuration. Finding feasible grasp configurations for novel objects, however, is challenging because of the huge variety in shape and size of these objects. Moreover, possible configurations also depend on the specific kinematics of the robotic arm and hand in use. In this paper, we introduce a new grasp selection algorithm able to find object grasp poses based on previously demonstrated grasps. Assuming that objects with similar shapes can be grasped in a similar way, we associate to each demonstrated grasp a grasp template. The template is a local shape descriptor for a possible grasp pose and is constructed using 3d information from depth sensors. For each new object to grasp, the algorithm then finds the best grasp candidate in the library of templates. The grasp selection is also able to improve over time using the information of previous grasp attempts to adapt the ranking of the templates. We tested the algorithm on two different platforms, the Willow Garage PR2 and the Barrett WAM arm which have very different hands. Our results show that the algorithm is able to find good grasp configurations for a large set of objects from a relatively small set of demonstrations, and does indeed improve its performance over time.

am mg

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Probabilistic depth image registration incorporating nonvisual information

Wüthrich, M., Pastor, P., Righetti, L., Billard, A., Schaal, S.

In 2012 IEEE International Conference on Robotics and Automation, pages: 3637-3644, IEEE, Saint Paul, USA, 2012 (inproceedings)

Abstract
In this paper, we derive a probabilistic registration algorithm for object modeling and tracking. In many robotics applications, such as manipulation tasks, nonvisual information about the movement of the object is available, which we will combine with the visual information. Furthermore we do not only consider observations of the object, but we also take space into account which has been observed to not be part of the object. Furthermore we are computing a posterior distribution over the relative alignment and not a point estimate as typically done in for example Iterative Closest Point (ICP). To our knowledge no existing algorithm meets these three conditions and we thus derive a novel registration algorithm in a Bayesian framework. Experimental results suggest that the proposed methods perform favorably in comparison to PCL [1] implementations of feature mapping and ICP, especially if nonvisual information is available.

am mg

link (url) DOI [BibTex]

link (url) DOI [BibTex]

2008


no image
Pattern generators with sensory feedback for the control of quadruped locomotion

Righetti, L., Ijspeert, A.

In 2008 IEEE International Conference on Robotics and Automation, pages: 819-824, IEEE, Pasadena, USA, 2008 (inproceedings)

Abstract
Central pattern generators (CPGs) are becoming a popular model for the control of locomotion of legged robots. Biological CPGs are neural networks responsible for the generation of rhythmic movements, especially locomotion. In robotics, a systematic way of designing such CPGs as artificial neural networks or systems of coupled oscillators with sensory feedback inclusion is still missing. In this contribution, we present a way of designing CPGs with coupled oscillators in which we can independently control the ascending and descending phases of the oscillations (i.e. the swing and stance phases of the limbs). Using insights from dynamical system theory, we construct generic networks of oscillators able to generate several gaits under simple parameter changes. Then we introduce a systematic way of adding sensory feedback from touch sensors in the CPG such that the controller is strongly coupled with the mechanical system it controls. Finally we control three different simulated robots (iCub, Aibo and Ghostdog) using the same controller to show the effectiveness of the approach. Our simulations prove the importance of independent control of swing and stance duration. The strong mutual coupling between the CPG and the robot allows for more robust locomotion, even under non precise parameters and non-flat environment.

mg

link (url) DOI [BibTex]

2008


link (url) DOI [BibTex]


no image
Experimental Study of Limit Cycle and Chaotic Controllers for the Locomotion of Centipede Robots

Matthey, L., Righetti, L., Ijspeert, A.

In 2008 IEEE/RSJ International Conference on Intelligent Robots and Systems, pages: 1860-1865, IEEE, Nice, France, sep 2008 (inproceedings)

Abstract
In this contribution we present a CPG (central pattern generator) controller based on coupled Rossler systems. It is able to generate both limit cycle and chaotic behaviors through bifurcation. We develop an experimental test bench to measure quantitatively the performance of different controllers on unknown terrains of increasing difficulty. First, we show that for flat terrains, open loop limit cycle systems are the most efficient (in terms of speed of locomotion) but that they are quite sensitive to environmental changes. Second, we show that sensory feedback is a crucial addition for unknown terrains. Third, we show that the chaotic controller with sensory feedback outperforms the other controllers in very difficult terrains and actually promotes the emergence of short synchronized movement patterns. All that is done using an unified framework for the generation of limit cycle and chaotic behaviors, where a simple parameter change can switch from one behavior to the other through bifurcation. Such flexibility would allow the automatic adaptation of the robot locomotion strategy to the terrain uncertainty.

mg

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Wetting and premelting of triple junctions and grain boundaries in the Al-Zn alloys

Straumal, B., Kogtenkova, O., Protasova, S., Mazilkin, A., Zieba, P., Czeppe, T., Wojewoda-Budka, J., Faryna, M.

In 495, pages: 126-131, Alicante, Spain, 2008 (inproceedings)

mms

DOI [BibTex]

DOI [BibTex]


no image
A Dynamical System for Online Learning of Periodic Movements of Unknown Waveform and Frequency

Gams, A., Righetti, L., Ijspeert, A., Lenarčič, J.

In 2008 2nd IEEE RAS & EMBS International Conference on Biomedical Robotics and Biomechatronics, pages: 85-90, IEEE, Scottsdale, USA, October 2008 (inproceedings)

Abstract
The paper presents a two-layered system for learning and encoding a periodic signal onto a limit cycle without any knowledge on the waveform and the frequency of the signal, and without any signal processing. The first dynamical system is responsible for extracting the main frequency of the input signal. It is based on adaptive frequency phase oscillators in a feedback structure, enabling us to extract separate frequency components without any signal processing, as all of the processing is embedded in the dynamics of the system itself. The second dynamical system is responsible for learning of the waveform. It has a built-in learning algorithm based on locally weighted regression, which adjusts the weights according to the amplitude of the input signal. By combining the output of the first system with the input of the second system we can rapidly teach new trajectories to robots. The systems works online for any periodic signal and can be applied in parallel to multiple dimensions. Furthermore, it can adapt to changes in frequency and shape, e.g. to non-stationary signals, and is computationally inexpensive. Results using simulated and hand-generated input signals, along with applying the algorithm to a HOAP-2 humanoid robot are presented.

mg

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Passive compliant quadruped robot using central pattern generators for locomotion control

Rutishauser, S., Sproewitz, A., Righetti, L., Ijspeert, A.

In 2008 IEEE International Conference on Biomedical Robotics and Biomechatronics, pages: 710-715, IEEE, Scottsdale, USA, October 2008 (inproceedings)

Abstract
We present a new quadruped robot, ldquoCheetahrdquo, featuring three-segment pantographic legs with passive compliant knee joints. Each leg has two degrees of freedom - knee and hip joint can be actuated using proximal mounted RC servo motors, force transmission to the knee is achieved by means of a bowden cable mechanism. Simple electronics to command the actuators from a desktop computer have been designed in order to test the robot. A Central Pattern Generator (CPG) network has been implemented to generate different gaits. A parameter space search was performed and tested on the robot to optimize forward velocity.

mg

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Study of the intermixing of Fe\textendashPt multilayers by analytical and high-resolution transmission electron microscopy

Sigle, W., Kaiser, T., Goll, D., Goo, N. H., Srot, V., van Aken, P. A., Detemple, E., Jäger, W.

In EMC2008, 14th European Microscopy Congress, Vol. 2: Materials Science, pages: 109-110, Springer, Aachen, Germany, 2008 (inproceedings)

mms

DOI [BibTex]

DOI [BibTex]


no image
A modular bio-inspired architecture for movement generation for the infant-like robot iCub

Degallier, S., Righetti, L., Natale, L., Nori, F., Metta, G., Ijspeert, A.

In 2008 2nd IEEE RAS & EMBS International Conference on Biomedical Robotics and Biomechatronics, pages: 795-800, IEEE, Scottsdale, USA, October 2008 (inproceedings)

Abstract
Movement generation in humans appears to be processed through a three-layered architecture, where each layer corresponds to a different level of abstraction in the representation of the movement. In this article, we will present an architecture reflecting this organization and based on a modular approach to human movement generation. We will show that our architecture is well suited for the online generation and modulation of motor behaviors, but also for switching between motor behaviors. This will be illustrated respectively through an interactive drumming task and through switching between reaching and crawling.

mg

link (url) DOI [BibTex]

link (url) DOI [BibTex]

2007


no image
Hand placement during quadruped locomotion in a humanoid robot: A dynamical system approach

Degallier, S., Righetti, L., Ijspeert, A.

In 2007 IEEE/RSJ International Conference on Intelligent Robots and Systems, pages: 2047-2052, IEEE, San Diego, USA, 2007 (inproceedings)

Abstract
Locomotion on an irregular surface is a challenging task in robotics. Among different problems to solve to obtain robust locomotion, visually guided locomotion and accurate foot placement are of crucial importance. Robust controllers able to adapt to sensory-motor feedbacks, in particular to properly place feet on specific locations, are thus needed. Dynamical systems are well suited for this task as any online modification of the parameters leads to a smooth adaptation of the trajectories, allowing a safe integration of sensory-motor feedback. In this contribution, as a first step in the direction of locomotion on irregular surfaces, we present a controller that allows hand placement during crawling in a simulated humanoid robot. The goal of the controller is to superimpose rhythmic movements for crawling with discrete (i.e. short-term) modulations of the hand placements to reach specific marks on the ground.

mg

link (url) DOI [BibTex]

2007


link (url) DOI [BibTex]


no image
Lower body realization of the baby humanoid - ‘iCub’

Tsagarakis, N., Becchi, F., Righetti, L., Ijspeert, A., Caldwell, D.

In 2007 IEEE/RSJ International Conference on Intelligent Robots and Systems, pages: 3616-3622, IEEE, San Diego, USA, 2007 (inproceedings)

Abstract
Nowadays, the understanding of the human cognition and it application to robotic systems forms a great challenge of research. The iCub is a robotic platform that was developed within the RobotCub European project to provide the cognition research community with an open baby- humanoid platform for understanding and development of cognitive systems. In this paper we present the design requirements and mechanical realization of the lower body developed for the "iCub". In particular the leg and the waist mechanisms adopted for lower body to match the size and physical abilities of a 2 frac12 year old human baby are introduced.

mg

link (url) DOI [BibTex]

link (url) DOI [BibTex]

2003


no image
Grain boundary phase transitions in the Al-Mg system and their influence on high-strain rate superplasticity

Straumal, B. B., Lopez, G. A., Mittemeijer, E. J., Gust, W., Zhilyaev, A. P.

In 216-217, pages: 307-312, Moscow, Russia, 2003 (inproceedings)

mms

[BibTex]

2003


[BibTex]


no image
Influence of grain boundary phase transitions on the diffusion-related properties

Straumal, B., Baretzky, B.

In Proceedings of the International Conference on Diffusion, Segregation and Stresses in Materials, pages: 53-64, Defect and Diffusion Forum, Scitec Publications Ltd., Moscow, Russia, 2003 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Are carbon nanostructures an efficient hydrogen storage medium?

Hirscher, M., Becher, M., Haluska, M., von Zeppelin, F., Chen, X., Dettlaff-Weglikowska, U., Roth, S.

In 356-357, pages: 433-437, Annecy, France, 2003 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Grain boundary faceting phase transition and thermal grooving in Cu

Straumal, B. B., Polyakov, S. A., Bischoff, E., Mittemeijer, E. J., Gust, W.

In Proceedings of the International Conference on Diffusion, Segregation and Stresses in Materials, 216/217, pages: 93-100, Diffusion and Defect Data, Pt. A, Defect and Diffusion Forum, Scitec Publ., Moscow, 2003 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Evolution of Fault-tolerant Self-replicating Structures

Righetti, L., Shokur, S., Capcarre, M.

In Advances in Artificial Life, pages: 278-288, Lecture Notes in Computer Science, Springer Berlin Heidelberg, 2003 (inproceedings)

Abstract
Designed and evolved self-replicating structures in cellular automata have been extensively studied in the past as models of Artificial Life. However, CAs, unlike their biological counterpart, are very brittle: any faulty cell usually leads to the complete destruction of any emerging structures, let alone self-replicating structures. A way to design fault-tolerant structures based on error-correcting-code has been presented recently [1], but it required a cumbersome work to be put into practice. In this paper, we get back to the original inspiration for these works, nature, and propose a way to evolve self-replicating structures, faults here being only an idiosyncracy of the environment.

mg

link (url) DOI [BibTex]

link (url) DOI [BibTex]


no image
Grain boundary faceting phase transition and thermal grooving in Cu

Straumal, B. B., Polyakov, S. A., Bischoff, E., Mittemeijer, E. J., Gust, W.

In Proceedings of the International Conference on Diffusion, Segregation and Stresses in Materials, 216/217, pages: 93-100, Diffusion and Defect Data, Pt. A, Defect and Diffusion Forum, Scitec Publ., Moscow, 2003 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Coercivity mechanism in nanocrystalline and bonded magnets

Goll, D., Kronmüller, H.

In Bonded Magnets. Proceedings of the NATO Advanced Research Workshop on Science and Technology of Bonded Magnets, 118, pages: 115-127, NATO Science Series: Series 2, Mathematics, Physics and Chemistry, Kluwer Acad. Publ., Newark, USA, 2003 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Investigation of Electromigration in Copper Interconnects by Noise Measurements

Emelianov, V., Ganesan, G., Puzic, A., Schulz, S., Eizenberg, M., Habermeier, H., Stoll, H.

In Noise as a Tool for Studying Materials, pages: 271-281, Proceedings of SPIE, Santa Fe, New Mexico, 2003 (inproceedings)

mms

[BibTex]

[BibTex]

2002


no image
Pressure Isotherms of Hydrogen Adsorption in Carbon Nanostructures

Chen, X., Dettlaff-Weglikowska, U., Haluska, M., Hulman, M., Roth, S., Hirscher, M., Becher, M.

In Making Functional Materials with Nanotubes, pages: Z9.11.1-Z9.11.6, Materials Research Society Symposium Proceedings, MRS, Boston [Mass.], 2002 (inproceedings)

mms

[BibTex]

2002


[BibTex]


no image
Hydrogen Storage in Carbon SWNTs: Atomic or Molecular?

Haluska, M., Hirscher, M., Becher, M., Dettlaff-Weglikowska, U., Chen, X., Roth, S.

In Structural and Electronic Properties of Molecular Nanostructures, pages: 601-605, AIP Conference Proceedings, AIP, Kirchberg, Tirol [Austria], 2002 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Hydrogen Storage in Nanostructured Carbon Materials at Room Temperature

Chen, X., Dettlaff-Weglikowska, U., Haluska, M., Hirscher, M., Becher, M., Roth, S.

In Structural and Electronic Properties of Molecular Nanostructures, pages: 597-600, AIP Conference Proceedings, AIP, Kirchberg, Tirol [Austria], 2002 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Micromagnetism and the microstructure of the cell walls in Sm2Co17 based permanent magnets

Goll, D., Hadjipanayis, G. C., Kronmüller, H.

In Proceedings of the 17th International Workshop on Rare-Earth Magnets and their Applications, pages: 696-703, Rinton Press, Newark, Delaware, USA, 2002 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Ab-initio study of the influence of epitaxial strain on magnetoelastic properties

Komelj, M., Fähnle, M.

In Atomistic Aspects of Epitaxial Growth, pages: 439-447, NATO Science series: Series 2, Mathematics, Physics, and Chemistry, Kluwer Academic Publishers, Dassia, Corfu [Greece], 2002 (inproceedings)

mms

[BibTex]

[BibTex]

2001


no image
Computational micromagnetism of magnetic structures and magnetization processes in thin plantelets and small particles

Kronmüller, H., Hertel, R.

In Magnetic Storage Sstems Beyond 2000, 41, pages: 345-362, Nato Science Series II: Mathematics, Physics and Chemistry, Kluwer Academic Publishers, Rhodos, Greece, 2001 (inproceedings)

mms

[BibTex]

2001


[BibTex]


no image
Hydrogen storage in mechanically treated single wall carbon nanotrubes

Haluska, M., Hulman, M., Hirscher, M., Becher, M., Roth, S., Stepanek, I., Bernier, P.

In Electronic Properties of Molecular Nanostructures: XV International Winterschool/Euroconference, 591, pages: 603-608, American Institute of Physics Conference Proceedings, AIP, Kirchberg [Austria], 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Isotopic mass and lattice constant of Si and Ge: X-Ray standing wave measurements

Zegenhagen, J., Kazimirov, A., Cao, L. X., Konuma, M., Sozontov, E., Plachke, D., Carstanjen, H. D., Bilger, G., Haller, E., Kohn, V., Cardona, M.

In Proceedings of the 25th Conference on the Physics of Semiconductors, 87, pages: 125-127, Springer proceedings in physics, Springer, Osaka, Japan, 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Positron Annihilation Studies on Stable and Undercooled Metal Melts at the Stuttgart Pelletron

Stoll, H., Siegle, A., Major, J.

In Application of Accelerators in Research and Industry, 576, pages: 749-752, AIP Conference Proceedings, Denton, Texas, USA, 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Submicrometer spatially resolved measurements of mechanical properties and correlation to microstructure and composition

Kunert, M., Baretzky, B., Baker, S. P., Mittemeijer, E. J.

In Fundamentals of Nanoindentation and Nanotribology II, 649, pages: Q3.2.1-Q3.2.6, Materials Research Society Symposium Proceedings, MRS, Boston, MA, USA, 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
The six-jump diffusion cycles in B2-compounds

Drautz, R., Meyer, B., Fähnle, M.

In Proceedings of DIMAT 2000, the Fifth International Conference on Diffusion in Materials, pages: 417-422, Defect and Diffusion Forum, Scitec Publications Ltd., Paris, France, 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Ionic nitriding of austenitic and ferritic steel with the aid of a high aperture hall current accelerator

Straumal, B. B., Vershinin, N. F., Friesel, M., Ishenko, S. A., Gust, W.

In Diffusion in Materials DIMAT2000, 194, pages: 1457-1462, Defect and Diffusion Forum, Trans Tech, Paris, France, 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
First proof of slow trapping of positronium in polymers by an Age-Momentum-Correlation (AMOC) experiment

Dauwe, C., Balcaen, N., van Waeyenberge, B., van Petegem, S., Stoll, H.

In Positron Annihilation. Proceedings of the 12th International Conference on Positron Annihilation, 363/365, pages: 254-256, Materials Science Forum, Trans Tech Publications Ltd., München, 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Positron-age-momentum correlation

Stoll, H., Bandzuch, P., Siegle, A.

In Positron Annihilation: Proceedings of the 12th International Conference on Positron Annihilation, 363-365, pages: 547-551, Materials Science Forum, Trans Tech Publications Ltd., München, 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Nanocrystalline and nanostructured high-performance permanent magnets

Goll, D., Hadjipanayis, G. C., Kronmüller, H.

In Applications of Ferromagnetic and Optical Materials, Storage and Magnetoelectronics, 674, pages: U2.4.1-U2.4.12, Materials Research Society Symposium Proceedings, MRS, San Francisco, Calif., 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Ion beam analysis with monolayer depth resolution using the electrostatic spectrometer at the MPI Stuttgart

Plachke, D., Blohm, G., Fischer, T., Khellaf, A., Kruse, O., Stoll, H., Carstanjen, H. D.

In Proceedings of the 16th International Conference on Applications of Accelerators in Research and Industry, 576, pages: 458-462, American Institute of Physics Conference Proceedings, AIP, Denton, Texas, 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
From the electronic structure to the macroscopiy behavior: A multi-scale analysis of plasticity in intermetallic compounds

Fähnle, M., Kohlhammer, S., Bester, G.

In Influences of Interface and Dislocation Behavior on Microstructure Evolution, 652, pages: Y4.5.1.-Y4.5.12, Materials Research Society Symposium Proceedings, MRS, Boston, Mass., USA, 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Influence of the microstructure on the magnetic properties of giant-magnetostrictive TbDyFe films

Hirscher, M., Winzek, B., Fischer, S. F., Kronmüller, H.

In Smart Materials. Proceedings of the 1st Caesarium, pages: 23-37, Springer, Bonn, 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Materials analysis with monolayer depth resolution using MeV ion beams

Carstanjen, H. D.

In 117, Las Vegas, USA, 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Flux-line pinning in low-angle grain boundaries.

Albrecht, J., Leonhardt, S., Kronmüller, H.

In Proceedings 10th International Workshop on Critical Currents (IWCC 2001), pages: 41-43, Göttingen, Germany, 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Measurement of the low-temperature self-diffusivity of lithium by elastic recoil detection analysis

Wieland, O., Carstanjen, H. D.

In Proceedings of DIMAT 2000, the Fifth International Conference on Diffusion in Materials, 194/199, pages: 35-41, Defect and Diffusion Forum, Scitec Publications Ltd., Paris, France, 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
From the electronic structure to the macroscopic behaviour: a multi-scale analysis of plasticity in intermetallic compounds

Fähnle, M., Kohlhammer, S., Bester, G.

In Influences of Interface and Dislocation Behavior on Microstructure Evolution, 652, pages: Y.4.5.1-Y.4.5.12, Materials Research Society Symposium Proceedings, MRS, Boston, Mass., 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
Enhancement of the critical current density of YBa2Cu3O7-8-films by substracte irradiation

Leonhardt, S., Albrecht, J., Warthmann, R., Kronmüller, H.

In High-Tc Superconductors and Related Applications: Materials Science, Fundamental Properties, and Some Future Electronic Applications. Proceedings of the NATO Advanced Study Institute, 86, pages: 529-534, NATO Science Series 3. High Technology, Kluwer Academic Publishers, Albena, Bulgaria, 2001 (inproceedings)

mms

[BibTex]

[BibTex]


no image
AMOC studies of positronium in fine MgO powder

van Waeyenberge, B., Dauwe, C., Stoll, H.

In Positron Annihilation. Proceedings of the 12th International Conference on Positron Annihilation, 363/365, pages: 401-403, Materials Science Forum, Trans Tech Publications Ltd., München, 2001 (inproceedings)

mms

[BibTex]

[BibTex]